Battery Charger. 2024 Jeep Wagoneer 3.0L Twin Turbo I6 4WD

Sold by RedArc, the 100 amp Fuse Kit is designed for Smart Battery Isolator installations. Equipped with the best quality fuses and fuse holders, the kit has the cable needed for a specified current to make a solid connection, providing peace of mind for a safe and efficient installation. Kit includes: 2 x fuse holders, 4 x 40 amp fuses, cable crimps, and detailed instructions.

Sold by RedArc, the 1000W Pure Sine Wave Inverter makes it possible to plug in anywhere and power all your 110 volt luxuries from home. With a 1000W inverter in your off-grid setup, you can charge your phones, cameras, laptops and speakers, and run GPS and CPAP machines, without fear of damaging your appliances. Slimmer and lighter, RedArc inverters feature multiple levels of protection including overload, short circuit and an over temperature and load controlled cooling fan, which is engaged when power consumption reaches a certain level. This ensures the inverter can work comfortably in even the harshest conditions.

Sold by RedArc, the GoBlock is both a portable power source and flexible in-vehicle dual battery system. With USB, accessory, merit, fridge and Anderson outputs, the GoBlock is ideal for charging smart devices, phones, games, cameras and drones as well as powering lights, compressors, a portable fridge and more. Featuring a 100 amp lithium (LiFePO4) battery, the GoBlock is capable of a rapid 50 amp recharge rate utilizing RedArcÆs proprietary DC charging technology. Including a start battery recovery feature, the GoBlock can safely charge a vehicleÆs start battery to get a vehicle out of trouble on the road in just 15 minutes. Utilizing built-in MPPT solar regulator technology, the GoBlock gets the most out of any solar panels. With three ways to charge, utilize 50 amp of fast charge via the vehicleÆs alternator, trickle charge via the vehicleÆs accessory socket, charge via shore power while at home or solar while parked at camp. The GoBlock connects via Bluetooth to REDARCÆs RedVision smartphone app, providing remote access to the battery state of charge, system diagnostics, input source information and the ability to activate Start Battery Recovery mode. Install the GoBlock into vehicles with either standard or smart alternator systems, meaning itÆs suitable for any vehicle installation. Being portable, it can be moved between vehicles for power anywhere or mounted securely with the PowerDock. The GoBlock is built tough with a rugged exterior, meaning itÆs prepared for almost any situation. With an IP52 protection rating, its inputs and outputs are neatly recessed with tough shields to protect them from hard knocks and inclement weather. The battery is made of high-quality lithium cells that are safely enclosed within the fully sealed aluminium case.

Sold by CTEK, the 12V Battery Analyzer tests the condition of all types of 12V lead-acid batteries including Wet, Maintenance Free, Ca/Ca, Gel and AGM with high accuracy. Easy to use, it provides fast and easy-to-understand results. Operating voltage range is 8û15V with a test range of 200û1200EN. Simply connect the clamps to the battery and follow the step-by-step instructions on the display. The easy-to-read display gives clear information on the condition of any 12V lead-acid battery and advises what action is required. With no need to disconnect the battery from the vehicle, the patented technology used by the CTEK Battery Analyzer is safe for the user and vehicle electronics. It is reverse polarity protected, creates no battery loads, heat or sparks. Features include ease of use ù simply attach to the battery (no need to disconnect) and follow the on-screen instructions, provides fast, accurate results ù the CTEK Battery Analyzer tests the battery in seconds providing an instant on-screen result which advises what action should be taken, safe ù the patented technology not only provides fast, accurate results but undertakes the test without placing a load on the battery and generates no potentially dangerous heat or sparks and works equally well with all lead-acid battery types and requires no adjustment to perform an accurate test. This product carries a two-year warranty.

Sold by RedArc, the 1500W Pure Sine Wave Inverter makes it possible to plug in anywhere and power all your 110 volt luxuries from home. With a 1500W inverter in your off-grid setup, you can charge your phones, cameras, laptops and speakers, and run GPS and CPAP machines, without fear of damaging your appliances. Slimmer and lighter, RedArc inverters feature multiple levels of protection including overload, short circuit and an over temperature and load controlled cooling fan, which is engaged when power consumption reaches a certain level. This ensures the inverter can work comfortably in even the harshest conditions.

Sold by RedArc, the 160W monocrystalline solar blanket is lightweight, compact, and rugged, and the ultimate in portable solar power. The monocrystalline solar blankets are constructed from heavy duty canvas and covered in an anti-reflective and scratch resistant ethylene tetrafluoroethylene (ETFE) coating, improving efficiency and making them extremely durable, perfect for off-road conditions. Bypass diodes connect each solar window, minimizing the impact of shadows making them the best solar panels for camping. With genuine industry standard Anderson SB 50 connectors, setting up camp is easier than ever. These high-quality Anderson plugs are simple and fast to connect with no screw terminals and no risk of poor connections from frayed wires or loose terminals, just plug and play.

Sold by RedArc, the 2000W Pure Sine Wave Inverter makes it possible to plug in anywhere and power all your 110 volt luxuries from home. With a 2000W inverter in your off-grid setup, you can charge your phones, cameras, laptops and speakers, and run GPS, CPAP, coffee machines, hairdryers, microwaves, irons and power tools without fear of damaging your appliances. Slimmer and lighter, RedArc inverters feature multiple levels of protection including overload, short circuit and an over temperature and load controlled cooling fan, which is engaged when power consumption reaches a certain level. This ensures the inverter can work comfortably in even the harshest conditions.

Sold by RedArc, the 23 amp Fuse Kit is equipped with high-quality fuses and a fuse holder. Designed for the specified current and required to make a solid connection, this ensures any installation is working safely and efficiently. The kit includes: 1 x fuse holder, 2 x 23 amp fuses, cable crimps and detailed instructions.

Sold by RedArc, the 1240W monocrystalline solar blanket is lightweight, compact, and rugged and is the ultimate in portable solar power. The monocrystalline solar blankets are constructed from heavy duty canvas and covered in an anti-reflective and scratch resistant ethylene tetrafluoroethylene (ETFE) coating, improving efficiency and making them extremely durable, perfect for off-road conditions. Bypass diodes connect each solar window, minimizing the impact of shadows making them the best solar panels for camping. With genuine industry standard Anderson SB 50 connectors, setting up camp is easier than ever. These high-quality Anderson plugs are simple and fast to connect with no screw terminals and no risk of poor connections from frayed wires or loose terminals, just plug and play.

Sold by RedArc, the 30 amp Fuse Kit is equipped with high-quality fuses and a fuse holder. Designed for the specified current and required to make a solid connection, this ensures installation is working safely and efficiently. The kit includes: 1 x fuse holder, 2 x 30 amp fuses, cable crimps and detailed instructions.

Sold by RedArc, the 3000W Pure Sine Wave Inverter makes it possible to plug in anywhere and power all your 110 volt luxuries from home. With a 3000W inverter in your off-grid setup, you can charge your phones, cameras, laptops and speakers, and run GPS, CPAP, coffee machines, hairdryers, heaters, kettles, microwaves, irons and power tools without fear of damaging your appliances. Slimmer and lighter, RedArc inverters feature multiple levels of protection including overload, short circuit and an over temperature and load controlled cooling fan, which is engaged when power consumption reaches a certain level. This ensures the inverter can work comfortably in even the harshest conditions.

Sold by RedArc, the 300W monocrystalline solar blanket is lightweight, compact, and rugged and the ultimate in portable solar power. The monocrystalline solar blankets are constructed from heavy duty canvas and covered in an anti-reflective and scratch resistant ethylene tetrafluoroethylene (ETFE) coating, improving efficiency and making them extremely durable, perfect for off-road conditions. Bypass diodes connect each solar window, minimising the impact of shadows making them the best solar panels for camping. With genuine industry standard Anderson SB 50 connectors, setting up camp is easier than ever. These high-quality Anderson plugs are simple and fast to connect with no screw terminals and no risk of poor connections from frayed wires or loose terminals, just plug and play.

Sold by RedArc, the 40 amp Fuse Kit is equipped with high-quality fuses and a fuse holder. Designed for the specified current and required to make a solid connection, this ensures installation is working safely and efficiently. The kit includes: 2 x fuse holders, 4 x 40 amp fuses, cable crimps and detailed instructions.

Sold by RedArc, the 400W Pure Sine Wave Inverter makes it possible to plug in anywhere and power all your 110 volt luxuries from home. With a 400W inverter in your off-grid setup, you can charge your phones, cameras, laptops and speakers, and run GPS and CPAP machines, without fear of damaging your appliances. Slimmer and lighter, RedArc inverters feature multiple levels of protection including overload, short circuit and an over temperature and load controlled cooling fan, which is engaged when power consumption reaches a certain level. This ensures the inverter can work comfortably in even the harshest conditions.

Sold by RedArc, the 60 amp Fuse Kit is equipped with high-quality fuses and a fuse holder. Designed for the specified current and required to make a solid connection, this ensures installation is working safely and efficiently. The kit includes: 2 x fuse holders, 4 x 60 amp fuses, cable crimps, and detailed instructions.

Sold by Red Arc, the Alpha150 12 volt 150Ah Lithium Battery is the ultimate in performance with an extra-long lifespan and huge discharge rate. Benefit from a long cycle life of over 5000 cycles at 100% depth of discharge (DoD). With up to 60% longer lifespan than some lithium competitors, it's the ultimate lithium battery. Stay informed with Bluetooth connectivity and the intuitive companion app. State of charge and battery charge remaining are available at the touch of a button. Experience up to 70% more amp hours per cubic inch compart to key lithium competitors, meaning more power in a compact size to maximize storage space without compromising on performance. 30% more amp hours per pound than key lithium competitors, the Alpha150 is a lightweight solution for optimal weight distribution in any vehicle setup. With a continuous discharge of 200 amps, the Alpha150 effortlessly powers high-demand appliances such as a 2000W inverter, without the need for multiple batteries. Streamline installation and power distribution, connect multiple loads effortlessly with versatile terminal options. With a lightning-fast maximum charge rate of 135 amps, charge up to 80% faster than competitors and reduce charge time up to just 1.1 hours. The Alpha150Æs self-heating feature, charge form as low as -22 degrees F to 113 degrees F and discharge from -4 degrees F to 140 degrees F to conquer extreme climates with confidence. Enclosed in durable PC/ABS with an IP56 rating, the Alpha150 shrugs off vibration, dust or water. Crafted with precision in the Netherlands to meet the highest quality standards, including UL1642 and UN38.3, and FCC certifications.

Sold by RedArc, the Alpha150 battery tray simplifies installation and mounting of the Alpha150 12V 150Ah Lithium Battery. Featuring quick, simple installation the Alpha150 Battery Tray keeps your battery securely locked in position over the roughest terrain. This zinc-plated bracket allows for installation on the floor of a vehicle via ten countersunk fasteners and comes with instructions to complete the installation process.

Sold by RedArc, this 25 amp, 12 volt in-vehicle dual battery charger is designed to charge your secondary battery banks to 100% state of charge while on the move. Maximise the performance of secondary battery banks from 75-200Ah. Fully sealed to survive the harshest conditions and work flawlessly in engine bay installations, this charger has been proven to thrive in all types of terrain, including deep water crossings, and stand up against extreme vibration and heat (up to 176 degrees F). Have the reassurance and confidence that your batteries will be charged to their optimal levels, thanks to a unique multi-stage charging algorithm that provides specific charging profiles tailored to all common battery types including lithium (LiFePO4), AGM, GEL, standard lead acid and calcium. Featuring a Maximum Power Point Tracking (MPPT) solar regulator, it will charge from both solar and alternator power simultaneously. With built-in 'Green Power Priority' it will always select solar charging first, meaning less load on the vehicleÆs alternator. Suitable for both 12 and 24-volt vehicle systems, this charger will also work with either standard or variable/smart alternators. Made in Australia by RedArc, it has undergone testing in some of the harshest conditions on the planet, so itÆs tough enough to take anything nature can throw at it.

Sold by RedArc, this 40 amp, 12 volt in-vehicle dual battery charger is designed to charge your secondary battery banks to 100% state of charge while on the move. Maximise the performance of secondary battery banks over 200Ah. Fully sealed to survive the harshest conditions and work flawlessly in engine bay installations, it has been proven to thrive in all types of terrain, including deep water crossings, and stand up against extreme vibration and heat (up to 176 degress F). Have the reassurance and confidence that your batteries will be charged to their optimal levels, thanks to a unique multi-stage charging algorithm that provides specific charging profiles tailored to all common battery types including lithium (LiFePO4), AGM, GEL, standard lead acid and calcium. Featuring a Maximum Power Point Tracking (MPPT) solar regulator, it will charge from both solar and alternator power simultaneously. With built-in 'Green Power Priority' it will always select solar charging first, meaning less load on the vehicleÆs alternator. Suitable for both 12 and 24-volt vehicle systems, this charger will also work with either standard or variable/smart alternators. Made in Australia by RedArc, it has undergone testing in some of the harshest conditions on the planet, so itÆs tough enough to take anything nature can throw at it.

Sold by RedArc, the battery Manager30 features a color display, mobile phone connectivity, is a complete battery management system for charging auxiliary batteries used in RV and overlanding vehicles. Designed to charge and maintain auxiliary batteries by incorporating AC, DC and solar charging inputs, it also features an in-built MPPT solar regulator, battery isolator and remote battery monitor. The Manager30 represents a complete DC to DC charging and maintenance solution for all common battery types including standard lead acid, gel, calcium, AGM and lithium (LiFePO4). The æGreen Power PriorityÆ feature will always look for solar power before supplementing with vehicle power. Combined with a built-in Maximum Power Point Tracking solar regulator, youÆre guaranteed to get the most out of your solar. The Manager30Æs simple color display is designed to show auxiliary battery information and charge status, making it simple to see how long until auxiliary batteries are full or flat as well as other vital battery information. The Manager30 also connects to RedArc's RedVision smartphone app, allowing monitoring of the battery state of charge from mobile devices. Designed and manufactured in Australia and developed with ease of installation in mind, the Manager30 is compatible with all vehicle and alternator systems including variable voltage/smart alternators.

Sold by RedArc, the GoBlock Recovery Cable allows you to never worry about a flat battery again. Use these smart battery recovery cables along with your GoBlock to safely and effectively recover your start battery using the start battery recovery feature. You can safely charge yours, or your friend's start battery and get out of trouble in as little as 15 minutes. Fitted with a genuine Anderson connector, this cable measures 1.5m in length and includes alligator style clamps for quick and effective connection to the vehicle's battery.

Sold by CTEK, the Charger Bumper helps protect your charger and your vehicle from bumps and scratches. Made from durable silicon rubber, the Bumper fits snugly round the body of your charger for extra grip on slippery surfaces and comes with a two-year warranty.

Sold by CTEK, the Charger Bumper is a black silicon rubber case to protect both the charger and the vehicle's paintwork from being damaged by hitting hard surfaces or your vehicle. Designed to fit MUS 4.3, MXS 5.0, Lithium US, and CT5 Time To Go, and CT5 Powersport battery chargers.

Sold by CTEK, the Charger Bumper is a silicon rubber case to protect both the charger and the vehicle's paintwork from being damaged from hitting hard surfaces or your vehicle. The case is designed to fit the MULTI US 7002 and Murs 7.0 battery chargers.

Sold by CTEK, the Charger Bumper is a silicon rubber case to protect both the charger and the vehicle's paintwork from being damaged from hitting hard surfaces or your vehicle. The case is designed to fit the US 0.8 and UC 800 6V battery chargers.

Sold by CTEK, the Charger Wall Mount provides easy access to charger functions and is a practical and secure storage for your CTEK battery charger. It is compatible with 4.3 Polar, 4.3 Test & Charge, Lithium, MXS 5.0, CT5 Time-To-Go and CT5 Powersport.

Sold by CTEK, the Comfort Connect 12V Plug enables charging the battery through a 12V outlet. It eliminates hassle by allowing you to simply charge from within the car. It works perfectly with CTEKÆs battery charger with Comfort Connect, UC 800, MULTI US 3300, MULTI US 7002, US 0.8, MXS 5.0, CT5 TIME TO GO, Lithium US, CT5 Powersport and MUS 4.3. The socket in the vehicle must be live when the ignition is in the ôoffö position to charge your battery using this accessory. The Comfort Connect 12V Plug fits both 12-millimeter and 21-millimeter outlets and has maze-like strain relief for the userÆs safety.

Sold by CTEK, the 12V Socket extends the usage of your charger connector. It simplifies the connection of auxiliary equipment like GPS, mobile phones, handlebar heaters, and heated clothing. Designed to fit UC 800, MULTI US 3300, US 0.8, MUS 4.3, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time To Go battery chargers.

Sold by CTEK, the Comfort Connect Extension Cable extends the reach of your CTEK chargers up to 8.2 feet. Designed to fit US 0.8, MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, Murs 7.0, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time To Go battery chargers.

Sold by CTEK, the Comfort Connect M10 Eyelet is the ideal solution if your battery is difficult to get to, hidden or when you canÆt use clamps. Just connect the easy-to-fit eyelet terminals to the battery and charge as usual.

Sold by CTEK, the Comfort Connect M6 Eyelet (for smaller batteries like motorcycle/lawn tractor) gives you the opportunity to quickly and easily reach well-hidden batteries in the vehicle and satisfy all of your battery charging needs without any hassle. CTEK offers three different sizes depending on the type of battery terminals. There is no need to hassle with battery clamps every time, just permanently mount Comfort Connect on every battery that needs charging and easily charge and maintain the batteries after use for prolonged life. Designed to fit UC 800, MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, Murs 7.0, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time To Go battery chargers.

Sold by CTEK, the Comfort Connect M8 Eyelet (for top post batteries) gives you the opportunity to quickly and easily reach well-hidden batteries in the vehicle and satisfy all of your battery charging needs without any hassle. CTEK offers three different sizes depending on the type of battery terminals. There is no need to hassle with battery clamps every time, just permanently mount Comfort Connect on every battery that needs charging and easily charge and maintain the batteries after use for prolonged life. Designed to fit UC 800, MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, Murs 7.0, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time to Go battery chargers.

Sold by CTEK, the Comfort Connect-Plug Adapter allows older (pre-2008) models of CTEK chargers to be compatible with the new generation accessories. Just connect to the CTEK charger fitted with the old style connector and the unit immediately becomes ready for use with all our modern Comfort Connect and Comfort Indicator accessories. Cable length 4.7 inches.

Sold by CTEK, the Comfort Indicator 12V Plug allows charging through a vehicle's 12-volt socket. The connector has our intelligent comfort indicator which shows how much power is left in the battery. The socket in the vehicle must be live when the ignition is in the ôoffö position to charge your battery using this accessory. Compatible with CTEK US 0.8, MULTI US 3300, MUS 4.3, MUS 7002, MXS 5.0 Lithium US, CT5 Powersport and CT5 Time To Go.An indicator is the easiest way to monitor the charge in your battery. An accurate voltage reading for your battery is displayed two hours after youÆve used your vehicle. Green means the battery voltage is more than 12.65 V. No need for charging. Yellow means the battery voltage is between 12.4 and 12.65 V. ItÆs time to consider charging the battery. Red means the battery voltage is below 12.4 V. ItÆs definitely time to charge the battery.

Sold by CTEK, the Comfort Indicator Clamp is designed and developed to make the maintenance of the battery in a dealer showroom easy and convenient. The clamps easily show the status on the battery and therefore eliminates the risk of selling a car with a dead battery. CTEK Comfort Indicator Clamps can prolong the life expectancy of the battery as it makes sure it can always be fully charged and it indicates when the harmful sulfation process begins. Designed to fit MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time To Go battery chargers. An indicator is the easiest way to monitor the charge in your battery. An accurate voltage reading for your battery is displayed two hours after youÆve used your vehicle. Green means the battery voltage is more than 12.65 V. No need for charging. Yellow means the battery voltage is between 12.4 and 12.65 V. ItÆs time to consider charging the battery. Red means the battery voltage is below 12.4 V. ItÆs definitely time to charge the battery.

Sold by CTEK, the Comfort Indicator Eyelet is designed for permanent installation with a direct connection to the battery. For use with CTEK chargers, it enables you to charge batteries that are in hard to reach places or where using clamps is inconvenient or impossible. Should charging be required, plug in your CTEK charger and charge the battery. Extended cable length up to 19.6 inches. It is perfect for seasonal vehicles such as lawn mowers and jet skis as well as automotive. Designed to fit MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time To Go battery chargers. An indicator is the easiest way to monitor the charge in your battery. An accurate voltage reading for your battery is displayed two hours after youÆve used your vehicle. Green means the battery voltage is more than 12.65 V. No need for charging. Yellow means the battery voltage is between 12.4 and 12.65 V. ItÆs time to consider charging the battery. Red means the battery voltage is below 12.4 V. ItÆs definitely time to charge the battery.

Sold by CTEK, the Comfort Indicator Eyelet is designed for permanent installation with a direct connection to the battery. For use with CTEK chargers, it enables you to charge batteries that are in hard to reach places or where using clamps is inconvenient or impossible. Should charging be required, plug in your CTEK charger and charge the battery. Extended cable length 19.6 inches. Designed to fit MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time To Go battery chargers. The M8 Eyelet is practical for all automotive battery applications. An indicator is the easiest way to monitor the charge in your battery. An accurate voltage reading for your battery is displayed two hours after youÆve used your vehicle. Green means the battery voltage is more than 12.65 V. No need for charging. Yellow means the battery voltage is between 12.4 and 12.65 V. ItÆs time to consider charging the battery. Red means the battery voltage is below 12.4 V. ItÆs definitely time to charge the battery.

Sold by CTEK, the Comfort Indicator Panel is designed and developed to make the maintenance of the battery in the vehicle easy and convenient. It easily shows the status of the battery and makes sure that the battery always gets the care it needs. The CTEK Comfort Indicator Panel can prolong the life expectancy of the battery as it makes sure it can always be fully charged and indicates when the harmful sulfation process begins. Designed to fit MULTI US 3300, MULTI US 7002, US 0.8, MXS 5.0, Lithium US, CT5 Powersport, MUS 4.3 Test & Charge, MUS 4.3 Polar, and CT5 Time To Go battery chargers. An indicator is the easiest way to monitor the charge in your battery. An accurate voltage reading for your battery is displayed two hours after youÆve used your vehicle. Green means the battery voltage is more than 12.65 V. No need for charging. Yellow means the battery voltage is between 12.4 and 12.65 V. ItÆs time to consider charging the battery. Red means the battery voltage is below 12.4 V. ItÆs definitely time to charge the battery.

Sold by CTEK, the Comfort Indicator Panel is designed and developed to make the maintenance of the battery in the vehicle easy and convenient. It easily shows the status of the battery and makes sure that the battery always gets the care it needs. The CTEK Comfort Indicator Panel can prolong the life expectancy of the battery as it makes sure it can always be fully charged and indicates when the harmful sulfation process begins. Designed to fit MULTI US 3300, MULTI US 7002, US 0.8, MXS 5.0, Lithium US, CT5 Powersport, MUS 4.3 Test & Charge, MUS 4.3 Polar, and CT5 Time To Go battery chargers. The panel comes with no wire leads, but features flat pins so you can connect and run your own wiring. An indicator is the easiest way to monitor the charge in your battery. An accurate voltage reading for your battery is displayed two hours after youÆve used your vehicle. Green means the battery voltage is more than 12.65 V. No need for charging. Yellow means the battery voltage is between 12.4 and 12.65 V. ItÆs time to consider charging the battery. Red means the battery voltage is below 12.4 V. ItÆs definitely time to charge the battery.

Sold by CTEK, the Comfort Indicator Panel is designed and developed to make the maintenance of the battery in the vehicle easy and convenient. The Comfort Indicator Panel easily shows the status of the battery and makes sure that the battery always gets the care it needs. It can prolong the life expectancy of the battery as it makes sure it can always be fully charged and indicates when the harmful sulfation process begins. It is designed to fit MULTI US 3300, MULTI US 7002, US 0.8, MXS 5.0, Lithium US, CT5 Powersport, MUS 4.3 Test & Charge, MUS 4.3 Polar, and CT5 Time To Go battery chargers. An indicator is the easiest way to monitor the charge in your battery. An accurate voltage reading for your battery is displayed two hours after youÆve used your vehicle. Green means the battery voltage is more than 12.65 V. No need for charging. Yellow means the battery voltage is between 12.4 and 12.65 V. ItÆs time to consider charging the battery. Red means the battery voltage is below 12.4 V. ItÆs definitely time to charge the battery.

Sold by CTEK, the Comfort Indicator Pigtail converts an existing SAE quick connector into a sealed indicator of the status of your battery, therefore eliminating the need to re-install new eyelet terminals. It also opens up for charging with a CTEK 12 Volt charger. The CTEK Comfort Indicator can prolong the life expectancy of the battery as it makes sure the battery can always be fully charged and also indicates when the harmful sulfation process begins. Designed to fit MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time To Go battery chargers. An indicator is the easiest way to monitor the charge in your battery. An accurate voltage reading for your battery is displayed two hours after youÆve used your vehicle. Green means the battery voltage is more than 12.65 V. No need for charging. Yellow means the battery voltage is between 12.4 and 12.65 V. ItÆs time to consider charging the battery. Red means the battery voltage is below 12.4 V. ItÆs definitely time to charge the battery.

Sold by CTEK, the practical, lightweight, padded CS FREE Bag allows you to keep your charger with you wherever you go. It is tough, durable, and lightweight to protect your charger and keep it safe from the elements û wherever you take it. The CS Storage Case is made from heavy-duty 600D water-repellent nylon with a protective padded interior and a handy carrying handle. The smooth metal zip gives you quick access to your charger so itÆs ready to go whenever you need it. The case is 290mm x 200mm x 90 mm and carries a two-year warranty.

Sold by CTEK, the CS FREE« powers up your dead battery safely, without risk of damaging your battery or vehicle electronics. Charge and maintain any 12V lead-acid or lithium battery anywhere using a power outlet, solar or leisure battery power. It's an adaptive booster to power up dead batteries, and portable battery charger to charge your vehicle battery wherever you are. Say goodbye to jump cables and jump starters. The CS FREE« is a four-in-one, cutting-edge product in one portable unit û- adaptive booster, battery charger, smart maintainer, and hi-tech power bank. It is the ultimate all-in-one solution to quickly power up dead batteries and keep your vehicle batteries in peak condition wherever you are. Features include flexiblity to connect to a power outlet and turn the CS FREE« into a 5A smart battery charger, user-friendly, with straightforward operation and clear instructions, no need to select modesùsimply connect, and the CS FREE« will handle the rest, countdown function shows you when you have enough power to start the vehicle and the remaining time until your battery reaches a full charge, internal battery will remain fully charged for up to a year, always ready for when you need it, equipped with USB-C and USB-A outputs to charge devices such as laptops, smartphones, and tablets, s a new ergonomic design encased in a robust and durable housing, complete range of accessories available for handy storage and to give you complete freedom from a power outlet. This product carries a two-year ôpeace of mindö warranty.

Sold by CTEK, the CS FREE« Solar Panel Charge Kit lets you recharge your CS FREE« internal battery using just solar power. You can also use it to power the CS FREE« without connecting to a power outlet, so you can charge and maintain your vehicle battery wherever you are. The kit pairs perfectly with the CS FREE« battery charger as it delivers fast, reliable solar power so you can recharge or even independently power your CS FREE« wherever you take it. Made from super-tough fiberglass, you simply unfold it and connect it to your CS FREE« in seconds, giving you the ultimate freedom from power outlets. Charge and maintain your vehicle battery or charge up portable tech like smartphones, pads, and laptops, even when youÆre nowhere near a power outlet. The kit features intelligent and efficient silicon cells with a specially developed safety box so the kit delivers exactly the right amount of power to protect your battery and devices from excess voltage. Waterproof, weather-resistant, and durable, the CTEK CS FREE« Solar Panel Charget Kit is the perfect outdoors partner for the CS FREE«. Features include recharges your CS FREE« in just one hour, tough, waterproof, and weather-resistant, lightweight and portable, carrying case with adjustable kickstand for flexible 180¦ positioning.

Sold by CTEK, the CS FREE« USB-C Charge Cable quickly charges your CS FREE« in just one hour using your vehicleÆs 12V cigarette lighter or accessory socket, so itÆs ready whenever you need it. The 12V plug makes it safe and easy to charge your CS FREEÆs internal battery while youÆre on the move, or when your vehicle is parked. Simply plug it into your vehicleÆs 12V cigarette lighter or accessory socket and connect the USB-C plug to the CS FREEÆs charge input port. Please note that the socket must be powered even when the ignition is in the æOFFÆ position. The USB-C Charge Cable 12V plug has a tough, hardwearing, and flexible cable designed and rigorously tested.

Sold by CTEK, the USB-C Charge Cable Clamps allow you use a separate 12V service battery to power your CS FREE« without being connected to a power outlet. It is to power your CS FREE« quickly, safely, and easily from a 12V service battery. The clamps let you charge and maintain your vehicle battery wherever you are by simply attaching the red and black clamps to the service batteryÆs corresponding positive and negative terminals and connect the USB-C plug to the CS FREEÆs charge input port. The USB-C Charge Cable Clamps have tough, hardwearing, and tangle-free cables that have been rigorously tested.

Sold by CTEK, the CS Wall Mount keep your CS charger safe, secure, and accessible with this robust and versatile wall mount. The wall mount features CTEKÆs unique mounting system to hold your CS charger securely. Designed and tested in Sweden, this hard-wearing accessory can be permanently wall-mounted or temporarily hung on a hook. It gives you easy access to all your CS chargerÆs functions and has a practical clamp mount to keep your charger cables stored neatly. Features include practical, secure storage, a unique mounting system and flexibility to be fixed to the wall or hung safely on a hook.

Sold by CTEK, the CT5 TIME-TO-GO battery charger and maintainer is a world first because it answers the question æWhen will my battery be fully charged? The CT5 TIME-TO-GO gives you an accurate prediction of the remaining charging time in hours. Not only that, but itÆll also tell you when you can safely attempt to start your vehicle before the battery is fully charged. The CT5 TIME-TO-GO uses advanced technology to give you three charging and maintenance programs û Normal, AGM and Recond. ItÆs easy to use and fully automatic, so it can be connected directly to the battery indefinitely if required, and it wonÆt over or under charge. The CT5 also has built-in temperature sensing capabilities. Alligator clamps and eyelets included. Features include charging for all types of lead-acid 12V batteries (WET,EFB,MF,CA/CA,AGM AND GEL), tells you how long before the battery is charged and ready to go, indicator to tell you when you can try to start your vehicle after a dead battery, tully automatic charging with max 4.3A, tests and restores battery capacity, and non-sparking, reverse polarity protected and carries a five-year warranty.

Sold by CTEK, the Battery Sense Bluetooth Device makes it possible to show you the state of charge of all your batteries in real-time. It provides valuable knowledge about your batteries in a simple, user-friendly, and transparent way. Knowledge of your batteriesÆ charge level makes it easy to monitor each batteries' health status and thus maximize your battery performance and service life. This knowledge will allow you to avoid costly battery replacements and annoying vehicle breakdowns. Connect Battery Sense to the battery and download the app. Your batteries will now start talking to you via your smartphone. With Battery Sense connected, you donÆt have to worry about when to charge. Just walk to your car or vehicle and Battery Sense will communicate with you via your Bluetooth-enabled device, you donÆt even have to start the engine. Battery Sense will show you all your batteries' state of charge. The app will warn you when a battery requires charging well in advance of it reaching zero charge. Battery Sense comes with a two-year warranty and is designed to fit MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, MXS 5.0, CT5 Powersport, Murs 7.0 MUS 4.3 Polar, MUS 4.3 Test & Charge, and CT5 Time to Go battery chargers.

Sold by CTEK, the D250SE Charger is a fully-automatic, five-step charger that supplies up to 20A of power to any 12V lead-acid or lithium service battery (LiFePO4, Li-Fe, Li-iron, LFP). It has selectable charge algorithms for AGM and lithium batteries and can use power through its dual input from the alternator, solar panel, and wind power. When the service battery is fully charged, the D250SE will automatically redirect maintenance charge power to the starter battery. The D250SE can maintain a stable output up to 20A to vehicles Fitted with smart ECU controlled alternators and also has a temperature sensor for optimized charging, regardless of weather conditions. With award-winning Swedish technology, the dual input D250SE allows you to enjoy your vehicle more with maximized battery capacity as the ideal charger for vehicles without access to a main power supply. It carries a two-year warranty.

Sold by RedArc, the Encapsulated Protection Device has been designed to support the installation of RedArc's Tow-Pro Electric Brake Controllers. Utilised on vehicles where æback-feedÆ of 12 volt during the Tow-ProÆs Manual Override function may interfere with the vehicle systems, the Encapsulated Protection Devices is designed to fit in the Trailer Stop Lamp. When installed correctly, the device ensures correct trailer braking and stop lamp operation when the vehicle brakes or the Tow-Pro Manual Override is used. Rated at 7 Amps for both 12 volt and 24 volt applications, it is totally encapsulated with sealed connections.

Sold by RedArc, the GoBlock Inverter Connector Cable is designed to make connecting a 350W REDARC inverter to your GoBlock portable dual battery system a breeze. The GoBlock Inverter Connector Cable features lug terminals designed to connect to a 350W REDARC inverter, with an Anderson plug on the opposite end, offering a plug and play inverter solution.

Sold by RedArc, the GoBlock PowerDock provides a 50 amp fast charge and secure docking for the GoBlock Portable Dual Battery System. A semi-permanent installation solution, the PowerDock is lockable with anti-theft in mind and has been tested to suit relevant crash and vibration standards. Utilize the PowerDock as a secure way to transport the GoBlock, the patented design provides both restraint and connection with a single action mechanism. The PowerDock allows Green Power Priority charging for a GoBlock setup, providing simultaneous vehicle and solar charging that will utilize all available solar before supplementing with vehicle power. This reduces the load on a vehicleÆs electrical system and increases fuel economy.

The CTEK Lithium US Battery Charger is an advanced microprocessor-controlled charger specially designed to recharge and maintain the cells of Lithium-Iron (LiFePO4) batteries thus maximizing their performance and lifespan. With up to 4.3A of charge current available the Lithium US Battery Charger is extremely flexible and will charge LiFePO4 batteries from 5Ah to 60Ah and maintain up to 120Ah. The operation is simple and charging will commence upon connection. With no need to disconnect the battery from the vehicle, at charge start it will automatically reset any low voltage protection electronics (Battery Management System) fitted. Charging can be restarted manually at any time using the Reset button. The CTEK Lithium US Battery Charger is a fully automatic connect and forget charger with eight charging steps including a testing sequence to show if the LiFePO4 battery can take and retain the charge, a unique maximization step to restore full capacity, and patented maintenance charging to ensure maximum performance even after months of inactivity. Splash-proof and dust-proof (IP65) it is easy and safe to use, protects vehicle electronics, is spark-free, is reverse polarity protected and short circuit proof. This product carries a five-year warranty.

Sold by CTEK, this package is a kit of 50 M6 Eyelet mounts and CTEK Ready Stickers. Designed to fit UC 800, MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, Murs 7.0, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time to Go battery chargers.

Sold by CTEK, this package is a kit of 50 M8 Eyelet mounts and CTEK Ready Stickers. Designed to fit UC 800, MULTI US 3300, MULTI US 7002, US 0.8, MUS 4.3, Murs 7.0, MXS 5.0, Lithium US, CT5 Powersport and CT5 Time to Go battery chargers.

Sold by RedArc, the Universal Mounting Bracket allows an in-vehicle battery charger to be mounted in a vehicle engine bay when a model-specific mounting bracket is not available. Manufactured from robust 304 stainless steel, it positions the charger at the front of the vehicle where it will receive airflow and maintain optimal temperature. Included in this kit is everything needed for hassle-free installation including instructions, fasteners and the mounting bracket.

Sold by CTEK, the MUS 4.3 Polar Cold Weather Battery Charger has been specially developed to offer excellent all-around charging with special cold weather performance and adapted AC and DC cables to handle severe cold down to -22¦F (-30¦C). The MUS 4.3 Polar Cold Weather Battery Charger is an advanced microprocessor controlled battery charger providing unrivaled performance on batteries from 1.2Ah up to 110Ah. Features include the ability to diagnose a battery's condition to establish if it can receive and retain a charge, a patented automatic desulphation program, and a special reconditioning function that will revive and restore deeply discharged and stratified batteries. Snowflake mode ensures ideal charging performance even in the most extreme cold conditions. Patented Float/Pulse maintenance makes it ideal for long-term maintenance. The entire process of battery testing, charging, and maintenance is easily followed on the clear LED display. The MUS 4.3 Polar Cold Weather Battery Charger is a fully automatic connect and forget 12V charger with eight charging steps and offers selectable 0.8A and 4.3A programs. The Recond and Snowflake modes operate individually or together in both 0.8A and 4.3A programs providing great flexibility for the user. It has a wide charging range on all lead-acid battery types from 1.2Ah up to 110Ah with additional maintenance capability to 160Ah. Splash-proof and dust-proof (IP65), it is easy and safe to use, protects vehicle electronics, spark-free, reverse polarity protected, and short circuit proof. This product carries a five-year warranty. Alligator clamps and eyelets included.

Sold by CTEK, the MUS 4.3 Test&Charge Battery Charger/Tester combines an advanced microprocessor-controlled battery charger with a battery and alternator test function to provide the ultimate in battery testing, charging and maintenance. It provides excellent performance on batteries from 1.2Ah up to 110Ah. The charger solves a broad range of battery problems and features include a patented automatic desulphation program and a special reconditioning function that will revive and restore deeply discharged and stratified batteries. The patented Float/Pulse maintenance makes the charger ideal for long-term maintenance. The Recond and Snowflake modes operate individually or together in both 0.8A and 4.3A programs providing great flexibility for the user. It features three easy-to-use programs to test battery voltage, start power, and alternator performance to provide a complete picture of battery and vehicle charging system health. The MUS 4.3 Test&Charge Battery Charger/Tester is easy and safe to use, protects vehicle electronics, spark-free, reverse polarity protected and short circuit proof. The MUS 4.3 TEST&CHARGE features a 5-year warranty. Alligator clamps and eyelets included. This product carries a five-year warranty.

Sold by CTEK, the Multi US 7002 is the ideal universal battery charger for your camper, car, and boat. The battery charger is well suited for year-round use as it can stay connected for months. Thanks to its Supply mode, the battery charger provides power even without a battery. The Supply mode is indispensable when changing the battery as you avoid losing complicated program settings. It is perfect for vintage cars, boats with one battery, boats with start & service batteries, boats with start & service banks, scooters, motorcycles, Quads/ATVs, lawnmowers, RVs, and tractors (equipped with minimum 14Ah battery). The Multi US 7002 Includes two interchangeable connection leads, one with clamps and one with eyelet terminals.It has a unique eight-step charging curve. This newly refined technology developed by CTEK ensures that the vehicle's battery gets the best possible care. It even analyzes if the battery can hold the charge given. If it cannot, the battery is faulty and needs to be replaced. The CTEK chargers are developed for personal, vehicle, and battery safety. It is fully automatic for charging and maintenance. There is no need for any specific knowledge of batteries or their charging methods; the MULTI US 7002 will take care of that. Once you switch to the preferred mode, the charger takes its own readings and then begins to charge the battery in eight steps, including pulse maintenance for best performance and service life (arguably the most caring mode for a battery connected for a long time, a CTEK patented system). It is also perfectly suited for Optima Yellow Top batteries. Unused batteries lose their power and their life is shortened through sulphation. It is also more difficult to charge sulfated batteries. The MULTI US 7002 has a patented method for reconditioning sulfated batteries. The charger analyzes the state of the battery and, if possible, recovers the battery and its power. It is made for all weather conditions and situations and is prepared to charge and maintain, no matter the weather, temperature or situation. The MULTI US 7002 is extremely robust, water- and dust-resistant (IP65 classification) and is certified for use between -4¦F and +122¦F. Most vehicles today are equipped with sensitive electronic systems. Unlike less-sophisticated chargers, there is no need to disconnect the battery; the MULTI US 7002 is specially designed to not damage electronic systems. All CTEK models are designed to consider the safety of the user. They are spark-free, making the connection much easier and safer considering the gases batteries normally produce. The MULTI US 7002 is also protected from reverse-polarity connections and is short-circuit proof. A red light on the charger will simply indicate that the charging cannot begin until the user has connected the charger correctly. The Supply mode serves as a power supply unit that can run 12V equipment up to 7A. When changing a battery, important settings will therefore not be lost. The unique Recond mode restores the power capacity in a stratified battery, prolonging its life. The stratifying process starts after just a few deep discharges of the battery.

Sold by CTEK, the MXS 5.0 Battery Care Bundle is the perfect all-in-one kit for your vehicle and makes a great gift for family or friends - or for yourself!. The kit includes a CTEK 40-206 MXS 5.0-12 Volt Battery Charger, a CTEK 56-382 Comfort Connect Indicator Eyelet, a CTEK 56-915 Bumper, Comfort Connect Clamps and a CTEK Battery Bank/ External Battery for devices. The award-winning CTEK MXS 5.0, offers a unique eight-step approach to battery care. It works with all types of lead-acid 12V batteries (WET, EFB, MF, CA/CA, AGM, and GEL). ItÆs a fully automatic microprocessor controlled charger with a built-in automatic temperature sensor that features a unique combination of advanced charging modes and makes the new MXS 5.0 the fastest, most effective, and versatile consumer charger CTEK has ever made. The MXS 5.0 features capabilities for improved charging in all weather. It is the perfect charger for the user with multiple vehicle types and higher demand battery charging and maintenance requirements. The MXS 5.0 offers features such as a special reconditioning function that restores stratified and deeply discharged batteries, unique maintenance charging, and the charging of demanding AGM batteries (i.e. Optima). The charger is splash- and dust-proof, designed to protect vehicle electronics and non-sparking, reverse polarity protected, and short-circuit proof. This charger carries a five-year warranty and provides an outstanding charging experience! The CTEK Comfort Connect Indicator Eyelet is designed for permanent installation with a direct connection to the battery. It enables you to charge batteries that are in hard to reach places or where using clamps is inconvenient or impossible. The CTEK Bumper is a silicon rubber case designed to protect both the charger and the vehicleÆs paintwork from being damaged. THE CTEK Battery Bank/External Battery is styled to look like a miniature CTEK charger. The battery bank can be used to charge cell phones or tablets. The CTEK Battery Bank/External Battery isnÆt available for individual purchase, which makes it the perfect unique accessory for any CTEK user.

Sold by CTEK, the MXS 5.0 Charger features capabilities for improved charging in all weather. It is the perfect charger for the user with multiple vehicle types and higher demand battery charging and maintenance requirements. The MXS 5.0 offers features such as a special reconditioning function that restores stratified and deeply discharged batteries, unique maintenance charging, and the charging of demanding AGM batteries (i.e. Optima). The charger is splash- and dust-proof, designed to protect vehicle electronics, non-sparking, reverse-polarity protected, and short-circuit-proof. It's a fully automatic microprocessor-controlled charger with built-in automatic temperature sensor features and a unique combination of advanced charging modes which makes the new MXS 5.0 the fastest, most effective, and versatile consumer charger CTEK has ever made. Alligator clamps and eyelets included. The MXS 5.0 charges batteries up to 110AH and maintains larger batteries up to 160AH. It features a unique reconditioning mode, built-in temperature sensing capabilities, AGM and new EFB (enhanced flooded battery) battery charging capability, completely sealed unit, clean voltage and current, premium input and output cable with robust strain relief. The Charger carries a five-year warranty and works for all types of lead-acid 12V batteries (WET, EFB, MF, CA/CA, AGM, GEL).

Sold by RedArc, the Complete PowerDock Installation Kit includes everything you need to install the PowerDock in the rear of a vehicle for a reliable and fast GoBlock charge. The pre-terminated wiring and fuses to connect the PowerDock in the rear of a vehicle to the start battery in the engine bay makes the installation of a PowerDock easier than ever. A genuine Anderson connector and cable is also included to connect fixed or portable solar panels.

Sold by CTEK, the PRO Battery Tester is complete with an integrated printer. ItÆs now easier than ever to determine and present the current state of a battery and electrical system. The PRO Battery Tester performs quick, simple, and accurate battery or system tests in seconds without heat, sparks, or user interpretation. The results can then be printed and reviewed immediately with customers for added impact to preventative maintenance routines and customer service. The CTEK PRO Battery Tester is patented and features an integrated printer to provide immediate results to review with the customer, user-defined printout header, tests 12V batteries and electrical systems for cars and light trucks, tests starting and charging system voltage and displays results, bad cell detection, reverse polarity protection, tests discharged batteries down to 1V, multiple rating system compatible (CCA, DIN, EN, IEC, SAE), tests multiple battery chemistries: standard (flooded), AGM, and GEL and comes with a two-year warranty.

Sold by CTEK, the PRO25S Charger is an innovative, versatile, and highly efficient 25 A battery charger and power supply designed around the needs of the automotive professional. Combining power and advanced technology with safety, portability, and flexibility to work with any 12V vehicle battery including lithium (LiFePO4, Li-Fe, Li-iron, LFP), the PRO25S is the perfect solution to professional battery charging, in the workshop, or the showroom. Advanced technology will ensure that a safe, fast charge is delivered to exactly meet the needs of the individual battery. The PRO25S has a dedicated lead-acid battery reconditioning program to restore battery life and recondition dead batteries. Supply mode will support the battery during diagnostic or fault-finding work. It has low voltage and current ripple, so itÆs safe for the battery and the vehicleÆs delicate electronic systems. Fully automatic and easy to use, itÆs also very simple to connect, spark-proof, and reverse-polarity protected to protect the user and the battery. The PRO25S is designed to ensure easy handling in both the workshop and the showroom. ItÆs lightweight and portable, and the rugged, impact-resistant casing means it can also handle the toughest workshop environment. Features include compatibility with battery types 12V: WET, EFB, MF, Ca/Ca, AGM, GEL, LiFePO4, dedicated lithium mode (12V lithium batteries (LiFePO4, Li-Fe, Li-iron, LFP), built-in temperature sensor to achieve maximum charge levels, dedicated lead-acid reconditioning program to restore battery life and recondition dead batteries. This charger carries a two-year warranty.

Sold by CTEK, the PRO25SE Charger is an innovative, versatile, and highly efficient 25A battery charger and power supply. Supplied with 236 Inch charging cables, you can install the unit on ramp-posts or in work bays. Combining power and advanced technology with safety and compatibility to work with any 12V vehicle battery, including 12 V ithium batteries (LiFePO4, Li-Fe, Li-iron, LFP). ItÆs the perfect solution for battery charging in the professional workshop. Advanced technology will ensure that a safe, fast charge is delivered to exactly meet the needs of the individual battery. The PRO25SE has a dedicated lead-acid battery reconditioning program to restore battery life and recondition dead batteries. Supply mode will support the battery during diagnostic or fault-finding work. It has low voltage and current ripple, so itÆs safe for the battery and the vehicleÆs delicate electronic systems. Fully automatic and easy to use, itÆs also very simple to connect, spark-proof, and reverse-polarity protected to protect the user and the battery. The PRO25SE is designed to ensure easy handling in both the workshop and the showroom. Features include 19.6 ft. charging cables, wall hanger/bracket, mounting points within the casing for permanent installation on ramp posts or in work bays, compatibility with batteries from 40 Ah to 500 Ah (30 Ah to 450 Ah lithium, 12V lithium batteries (LiFePO4, Li-Fe, Li-iron, LFP), built-in temperature sensor to achieve maximum charge levels, lightweight and highly portable. This charger carries a two-year warranty.

Sold by CTEK, the PRO25SE comes with a 19.6 foot charging cable, wall hanger, and bracket with magnets to mount without drilling. Mounting points are within the casing for permanent installation on ramp posts or in work bays without drilling. Works with battery types 12V: WET, EFB, MF, Ca/Ca, AGM, GEL, LiFePO4 and compatible with batteries from 40 Ah to 500 Ah (30 Ah to 450 Ah lithium - 12V lithium batteries (LiFePO4, Li-Fe, Li-iron, LFP). Includes supply mode to support the battery during diagnostic or fault-finding work and dedicated lithium (12V lithium batteries (LiFePO4, Li-Fe, Li-iron, LFP) mode. Integrated safety features, itÆs safe for the battery and the vehicle. Built-in temperature sensor to achieve maximum charge levels. Fully automatic and easy to use. Simple to connect, spark-proof, and reverse-polarity protected. Dedicated lead-acid reconditioning program to restore battery life and recondition flat batteries. Lightweight, highly portable, tough and robust, it includes a two-year warranty.

Sold by RedArc, the RedVision Display Unit can be used as a replacement or secondary display for the Manager30 or RedVision Total Vehicle Management System. Featuring a modern, user-friendly interface and easy-to- understand system layout, this robust display has been built and tested to withstand the touches and most extreme environmental conditions while providing control of multiple on-board devices and visibility over battery power and water tank levels. The RedVision Display Unit can only be retro-fitted for use on the Manager30 with part number BMS1230S3-NA. The unit includes: 4.3-inch display, optional mounting spaces, display fascia, RJ45 R-Bus cable (15-inch black), and an RJ45 R-Bus terminating resistor.

Sold by RedArc, the Rogue Power Distribution Module is a total vehicle management system. Control accessories via the physical screen or your Bluetooth connected mobile device. At just one inch thick with built-in smart fusing, the TVMS Rogue offers a small footprint, great for vehicles with limited space. The TVMS Rogue allows complete control of multiple on-board devices including fans, fridges, inverters and pumps. Each of its 10 output channels include dimming and the built-in switch inputs make the Rogue perfect for lighting circuits. Save time and energy by using RedVision app to automate those tasks. With the press of a button, switch off everything except for your fridge or power down non-essential loads when your batteries are running low. RedVision Display is required and sold separately.

Sold by RedArc, the 25A Side-by-side Engine Bay Install Wiring Kit has been designed to facilitate easy installation of a RedArc battery charger when the start battery and auxiliary battery are in close proximity within the engine bay (less than two feet apart). This kit contains all the cables, fuses, fuse holders and connectors required to install the charger between the batteries. The cables come pre-crimped on one end and, through use of the supplied terminal block, the other end of the cables can be trimmed to length to suit the specific installation. The Wiring Kit includes brown, black and red cables, terminal block with plastic cover, M5 x 25mm socket head screw, M5 nylon locking nuts, M5 flat washer, six-inch red cable, fuse kit, cable ties, Wago connector and boot, blue cable and 39-inch protective conduit.

Sold by RedArc, the Smart Battery Monitor eliminates power anxiety and keeps track of battery levels in real time. Utilising the latest Bluetooth 5.1 technology, the Smart Battery Monitor delivers reliability over longer distances. Connect at distances up to 137 feet, nearly 1.5x further than the competition. Easily view battery levels and an estimate of how many days power remains, updated in real time, anywhere at camp. Up to five times more accurate than the leading competitor, trust that '2 Hours Left' means '2 Hours Left'. With just three connection points and convenient configuration app, get battery monitoring in minutes. Utilising REDARCÆs RedVision app, vital battery information including state of charge, charge remaining and current flow is available at the touch of a button. The Smart Battery Monitor is a simple addition to any 12 volt power system, making keeping track of auxiliary batteries simple. Each Smart Battery Monitor is designed, tested, and manufactured in Australia and backed by RedArcÆs leading technical support. Our rigorous testing ensures that the Smart Battery Monitor wonÆt fail when the road gets rough.

Sold by CTEK, the Trolley Pro enables you to carry all your battery management equipment such as a CTEK charger, laptop, batteries, and other analysis instruments together with this complete test station. With two large wheels, it is highly portable and can be used and maneuvered in small spaces. Includes hooks for handy cable storage. It's a complete mobile test station for a charger, computer, analysis instruments, and batteries. It's perfect for flash programming activity and all equipment is easy access. The Trolley Pro is of robust steel construction with large rubber wheels and black powder coating and weighs about 22 kg. The top plate load capacity is 10 kg and the bottom shelf load capacity is 25 kg. It is suitable for use with MUS 25000 and MXS 25EC.

Sold by RedArc, this 25 amp, 12V in-vehicle dual battery charger is designed to charge your secondary battery banks to 100% state of charge while on the move. Maximize the performance of secondary battery banks from 75-200Ah. Fully sealed to survive the harshest conditions and work flawlessly in engine bay installations, this charger has been proven to thrive in all types of terrain, including deep water crossings, and stand up against extreme vibration and heat (up to 176 degrees F. Have the reassurance and confidence that your batteries will be charged to their optimal levels, thanks to a unique multi-stage charging algorithm that provides specific charging profiles tailored to all common battery types including lithium (LiFePO4), AGM, GEL, standard lead acid and calcium. Featuring a Maximum Power Point Tracking (MPPT) solar regulator, this charger will charge from both solar and alternator power simultaneously. With built-in 'Green Power Priority' it will always select solar charging first, meaning less load on the vehicleÆs alternator. Suitable for both 12- and 24-volt vehicle systems, this charger will also work with either standard or variable/smart alternators. Made in Australia by RedArc, it has undergone testing in some of the harshest conditions on the planet, so itÆs tough enough to take anything nature can throw at it.

Sold by RedArc, this 40 amp, 12V in-vehicle dual battery charger is designed to charge your secondary battery banks to 100% state of charge while on the move. Maximize the performance of secondary battery banks over 200Ah. Fully sealed to survive the harshest conditions and work flawlessly in engine bay installations, this charger has been proven to thrive in all types of terrain, including deep water crossings, and stand up against extreme vibration and heat (up to 176 degrees F. Have the reassurance and confidence that your batteries will be charged to their optimal levels, thanks to a unique multi-stage charging algorithm that provides specific charging profiles tailored to all common battery types including lithium (LiFePO4), AGM, GEL, standard lead acid and calcium. Featuring a Maximum Power Point Tracking (MPPT) solar regulator, this charger will charge from both solar and alternator power simultaneously. With built-in 'Green Power Priority' it will always select solar charging first, meaning less load on the vehicleÆs alternator. Suitable for both 12- and 24-volt vehicle systems, this charger will also work with either standard or variable/smart alternators. Made in Australia by RedArc, it has undergone testing in some of the harshest conditions on the planet, so itÆs tough enough to take anything nature can throw at it.

Sold by RedArc, this 50 amp, 12V in-vehicle dual battery charger is designed to charge your secondary battery banks to 100% state of charge while on the move. Maximize the performance of secondary battery banks over 200Ah. Fully sealed to survive the harshest conditions and work flawlessly in engine bay installations, this charger has been proven to thrive in all types of terrain, including deep water crossings, and stand up against extreme vibration and heat (up to 176 degrees F. Have the reassurance and confidence that your batteries will be charged to their optimal levels, thanks to a unique multi-stage charging algorithm that provides specific charging profiles tailored to all common battery types including lithium (LiFePO4), AGM, GEL, standard lead acid and calcium. Featuring a Maximum Power Point Tracking (MPPT) solar regulator, this charger will charge from both solar and alternator power simultaneously. With built-in 'Green Power Priority' it will always select solar charging first, meaning less load on the vehicleÆs alternator. Suitable for both 12- and 24-volt vehicle systems, this charger will also work with either standard or variable/smart alternators. Made in Australia by RedArc, it has undergone testing in some of the harshest conditions on the planet, so itÆs tough enough to take anything nature can throw at it.

Sold by CTEK, the US 0.8 Battery Charger is CTEKÆs smallest 12V charger. It offers state of the art technology and is perfect for charging smaller 12V batteries that can be found in motorcycles, jet skis, ATVs, and lawnmowers. It is also suitable for maintenance charging normal- sized batteries such as car batteries. The unique display allows the user to follow the entire charging process. The US 0.8 Battery Charger is a compact and fully automatic six-step charger for 12V batteries from 1.2û32 Ah and is suitable for maintenance charging up to 100 Ah. It is splash- and dust-proof, delivers 0.8 A, and is designed to protect vehicle electronics. It is non-sparking, reverse polarity protected, and short circuit proof. Features include simplifying by using the same charger for multiple batteries, water-resistant so that the solution can be taken to the problem even if it rains or snows, patented maintenance charge for a unique combination of maximized life and performance, patented desulphation that extends the battery life, no sparks, short-circuit proof and reverse-polarity protected for untroubled usage. This product carries a five-year warranty. Alligator clamps and eyelets included.

Sold by CTEK, the Wall Hanger 300 has been specially designed to let you mount larger 300W CTEK chargers on walls, ramp posts or hang it off vehicle doors, making it perfect for workshops and garages. ItÆs plate screws directly onto the back of the charger and it also comes with a hook to help you store cables safely. The unit has durable rubber feet so you can place your charger on windshields or bodywork without scratching the vehicleÆs paintwork. It carries a two-year warranty and is designed for use with MUS 25000 (56-674).

Sold by CTEK, the Wall Hanger Pro is specially designed to allow the MUS25000, MXS 25EC, and PRO25S chargers to be mounted in an easy ôon-offö fashion on a wall, vehicle lift post, or hung on a vehicle door or window. The wall hanger has rubber feet to avoid scratching vehicle paintwork and includes a hook for safety and conveniently storing output cables and clips. Kit includes: charger mounting plate that attaches directly to the back of the charger, wall mounting plate with magnets for wall/surface mounting without drilling, screws and rubber feet.

Sold by RedArc, the 25 amp Rear Install Wiring Kit has been designed to facilitate easy installation of a RedArc BCDC1225D DC to DC Battery charger when the start battery and auxiliary battery are at opposite ends of the vehicle (up to 28 feet away from the start battery). This kit contains all the cables, fuses, fuse holders and connectors required to install the charger between the batteries. The cables come pre-crimped on one end and, through use of the supplied terminal block, the other end of the cables can be trimmed to length to suit the specific installation. The kit includes: brown, black and red cables, terminal block with plastic cover, M5 x 25mm socket head screw, M5 nylon locking nuts, M5 flat washer, 6-inch red cable, fuse kit, cable ties, wago connector and boot, blue cable, and 39-inch protective conduit.

Sold by RedArc, the 25A Across Engine Bay Wiring Kit The 25A Across Engine Bay Install Wiring Kit has been designed to facilitate easy installation of a RedArc BCDC1225D DC to DC Battery charger when the start battery and auxiliary battery are at opposite ends of the engine bay (more than 2 feet but less than 11 feet apart). This kit contains all the cables, fuses, fuse holders and connectors required to install the charger between the batteries. The cables come pre-crimped on one end and, through use of the supplied terminal block, the other end of the cables can be trimmed to length to suit the specific installation.

Sold by RedArc, the 50 amp Side-by-side Engine Bay Install Wiring Kit has been designed to facilitate easy installation of a RedArc BCDC1240D or BCDC1250D DC to DC Battery charger when the start battery and auxiliary battery are in close proximity within the engine bay (less than 2 feet apart). This kit contains all the cables, fuses, fuse holders and connectors required to install the charger between the batteries. The cables come pre-crimped on one end and, through use of the supplied terminal block, the other end of the cables can be trimmed to length to suit the specific installation. The Wiring Kit includes: brown, black and red cables, terminal block with plastic cover, M5 x 25mm socket head screw, M5 nylon locking nuts, M5 flat washer, 6-inch red cable, fuse kit, cable ties, wago connector and boot, blue cable, and 39-inch protective conduit.

Sold by RedArc, the 50 amp Across Engine Bay Install Wiring Kit has been designed to facilitate easy installation of a RedArc BCDC1240D or BCDC1250D DC to DC Battery charger when the start battery and auxiliary battery are at opposite ends of the engine bay (more than 2 feet but less than 11 feet apart). This kit contains all the cables, fuses, fuse holders and connectors required to install the charger between the batteries. The cables come pre-crimped on one end and, through use of the supplied terminal block, the other end of the cables can be trimmed to length to suit the specific installation. The Wiring Kit includes: brown, black and red cables, terminal block with plastic cover, M5 x 25mm socket head screw, M5 nylon locking nuts, M5 flat washer, 6-inch red cable, fuse kit, cable ties, wago connector and boot, blue cable and 39-inch protective conduit.

Sold by RedArc, the 50 amp Rear Install Wiring Kit has been designed to facilitate easy installation of a RedArc BCDC1240D or BCDC1250D DC to DC Battery charger when the start battery and auxiliary battery are at opposite ends of the vehicle (up to 28 feet away from the start battery). This kit contains all the cables, fuses, fuse holders and connectors required to install the charger between the batteries. The cables come pre-crimped on one end and, through use of the supplied terminal block, the other end of the cables can be trimmed to length to suit the specific installation. The Wiring Kit includes: brown, black and red cables, terminal block with plastic cover, M5 x 25mm socket head screw, M5 nylon locking nuts, M5 flat washer, 6-inch red cable, fuse kit, cable ties, wago connector and boot, blue cable and 39-inch protective conduit.

Sold by CTEK, the SMARTPASS 120S charges and supplies the service battery and equipment with 120A. Separate critical equipment from non-critical equipment ensuring that radio, emergency lights, and navigation systems always have power. SMARTPASS 120S is a 120A power management solution which distributes, controls and maximizes the available energy from your alternator to power service batteries and consumers. It handles all 12V batteries between 28û800Ah. It's Battery Guard function ensures that critical equipment such as radio, emergency lights and navigation systems always have power and take priority when the voltage on the service battery is low disconnecting non-critical consumers. The unitÆs Battery Guard will protect your service battery from total discharge and built-in over-temperature protection reduces charge current before the battery temperature gets too high. SMARTPASS 120S is compatible with the D250SA and D250SE 20A onboard chargers. Features include smart alternator compatible, quick recharge of batteries 28û800Ah and start assistance function.